ITI MRAC Fitting NIMI Mock Test MCQs

NCVT MIS ITI Online MCQ Mock Test of Trade MARC most Important Chapter Fitting MCQ Online Mock Test. latest NIMI mock most Important Question and Answer MCQ Collection of Trade MARC. According to NSQF Level – 5 Syllabus.

Fitting

Please Write your Name to show in Result

कंपोनेंट की माप लेते समय क्या निर्धारित किया जाता है?
What is determined when measuring a component?

बाहरी व्यास की संकेंद्रिकता जांचने के लिए निम्नलिखित में से कौन सा इंस्ट्रूमेंट प्रयोग में लाया जाता है?
Which of the following instruments is used to check the concentricity of the outer diameter?

मेटिंग पार्ट्स के बीच क्लीयरेंस को मापा जाता है
Clearance is measured between mating parts

थ्रेड रिंग गेज का प्रयोग किया जाता है?
Thread ring gauge is used for?

टेपर के कोण को परिशुद्धता में मापने के लिए निम्न में से किस इंस्ट्रूमेंट का प्रयोग किया जाता है?
Which of the following instruments is used to measure the angle of the taper with precision?

वर्नियर डेप्थ गेज का उपयोग किसे मापने के लिए करते हैं?
What is the vernier depth gauge used to measure?

किसी माइक्रोमीटर में 0.02 मिली मीटर का सकारात्मक त्रुटि है यदि माइक्रोमीटर 25.41मिलीमीटर माप देता है तो यह सही रीडिंग क्या होगी?
A micrometer has a positive error of 0.02 mm. If the micrometer reads 25.41 mm, what is the correct reading?

यदि किसी आउटसाइड माइक्रोमीटर के थिंबल डिवीजन की जीरो ग्रेजुएशन डेटम लाइन से नीचे रह जाती है जबकि माइक्रोमीटर के मेजरिंग फेसिंस में परस्पर संपर्क में है तब त्रुटि होती है
If the zero graduation of the thimble division of an outside micrometer remains below the datum line while the measuring faces of the micrometer are in contact with each other, then an error occurs.

ट्राई स्क्वायर के द्वारा किस कोण की चेकिंग कर सकते हैं?
Which angle can be checked by Tri square?

वर्नियर बैवल प्रोटेक्टर का लिस्ट काउंट कितना होता है?
What is the list count of vernier bevel protector?

साइन बार स्टैंडर्ड साइज में पाया जाता है निम्नलिखित में से साइन बार का कौन सा स्टैंडर्ड साइज नहीं है?
Sine bar is found in a standard size, which of the following is not a standard size of sine bar?

निम्नलिखित में से किस गेज का प्रयोग ऐसे सिलेंडरों को चेक करने के लिए किया जाता है जिन्हें ऊर्ध्वाधर या लंबवत स्थिति में ना रखा गया हो
Which of the following gauge is used to check cylinders which are not kept in a vertical position?

स्टील रूल की सहायता से कम से कम कितनी माप ली जा सकती है?
What is the least measurement that can be taken with the help of a steel rule?

किसी फीलर गेज का प्रयोग किया जाता है?
Is a feeler gauge used?

किसी माइक्रोमीटर में 0.03 मिलीमीटर का ऋणात्मक त्रुटि है यदि माइक्रोमीटर 40. 53 मिलीमीटर माप देता है तो सही रीडिंग क्या होती है?
A micrometer has a negative error of 0.03 mm. If the micrometer reads 40.53 mm, what is the correct reading?

Your score is

The average score is 17%

0%

MRAC Chapter Wise Mock Test